- Stock: In Stock
- Brand: SDI
- Reward Points: 13
- Model: Super Etch 12g Syringe
37% promotes strong bonding
Super Etch 37% wt phosphoric acid etchant for enamel and dentin.
Easily controlled Super Etch gel flows under direction, not under gravity.
37% wt phosphoric acid
30 to 40% wt phosphoric acid optimally etches in 15 to 20 seconds(1). Lower concentrations require longer contact time, unnecessarily delaying procedures.
Indications
• Enamel
• Dentin
In conjunction with all
• Adhesives
• Composites
• Compomers
• Glass ionomers
• Sealants
• Cements
To clean
• Porcelain
Blue tint gel
High visibility for precise placement.
No interference with adhesive
Super Etch inorganic silica gel thickener is no obstacle to the adhesive. Other etchants block adhesives with a wax-like polymer residue which can inhibit penetration and bonding.
Thixotropic gel
Super Etch non-slump gel offers precise placement. Agitate the gel to lower its viscosity.
Super Etch
Super Etch creates micropores in the enamel surface and removes the smear layer to unblock dentinal tubules. It promotes adhesive resin penetration and resin tag formation. Super Etch is vital for the restoration’s mechanical retention.
Dye free Etchant
A clear dye free 37% liquid etchant is also availale for patients who suffer dye allergies.
Super Etch syringes
Super Etch offers an easy to use, leak free syringe. Direct extrusion facilitates faster procedures, economical dispensing and easier access into difficult to reach areas.
Super Etch Low Viscosity (LV)
LV is specialized for sealants with a half gel / half liquid formulation. Super Etch LV’s high flowability achieves greater acid surface contact for deeper etchant penetration into pits and fissures. The deeper acid penetration strengthens the mechanical bond and the retention success of the sealant. Ideal for SDI’s Conseal f and all other sealants.
Super Etch syringe tips
Super Etch LV tips - 27 gauge pre-bent for minute pit and fissure crevasses. Super Etch tips - 23 gauge straight tips.
Instructions:-
For direct placement of all restorations.
Regular viscosity Super Etch
1. Clean and isolate tooth.
2. Etch tooth surface with Super Etch 37% phosphoric acid for 20 seconds.
3. Wash thoroughly with water.
4. Remove excess water. Keep moist.
5. Apply Stae dentin/enamel adhesive to saturate all internal surfaces, or bonding agent, according to manufacturer’s instruction.
6. Blow gently with dry, oil free air for 2 seconds to evaporate solvent. Leave surface glossy.
7. Light cure for 10 seconds.
8. 1. Place Wave / Wave MV / Wave HV fluoride releasing flowable composite or
8. 2. Place Ice (anterior/posterior) or Rok (posterior) composite
9. Light cure for 20 seconds in increments of 2mm
10. Polish and finish
for pit and fissure sealants
Low viscosity Super Etch LV
1. Clean and isolate tooth.
2. Etch tooth surface with Super Etch LV for at least 30 seconds, no more than 60 seconds
3. Wash thoroughly with water.
4. Completely dry tooth. Note: a dry field is essential for the following steps.
5. Directly inject or brush apply Conseal f pit and fissure sealant.
6. Light cure Conseal f for 20 seconds.
CAUTION: Ensure the dispensing tip hub is firmly attached to the Super Etch, Wave or Conseal f syringe by twisting the hub securely onto the syringe.
Packaging:-
12ml Syringes
Product | |
Product Name | Super Etch 12g Syringe |
Brand | SDI |
Made in | Ireland |
Use | For removes the smear layer to unblock dentinal tubules |
Category | Etchants |
Packaging | 12ml Syringes |
Warranty / Guarantee | 100% Genuine product |
Shipping Time | 2-3 Working Days |
Payment Mode | Credit Card, Debit Card, Net Banking, Wallets, Cash on Delivery |